产品中心
DR-712 Frequency-to-Analog Transmitter (One Input, Two Outputs)
所属分类:
Base Centralized Power Supply Series
● Single-input, dual-output frequency-isolated transmitter ● 24 V power supply; fully isolated three-port design—input, output, and power supply ● Easy to connect, low power consumption, long service life.
通道数:
One input, two outputs
输入:
0-100 Hz,0-1 kHz,0-5 kHz,0-10 kHz,User-specific parameters
配电:
输出:
0-5V,0~10V,1-5V,2-10V,4~20mA,0~20mA,User-specific parameters
供电方式:
24 VDC
产品详情
技术参数
技术与安装
下载

Close
- 产品对比
去对比
Basic Parameters |
|
| Number of channels | 1 in, 2 out |
| Output accuracy (20°C) | 0.2% F.S. |
| Temperature drift | 50ppm/K |
| Response time | 1s (0–90%) (TYP) |
| Dielectric strength | 1500 VAC for 1 minute, 2 mA |
| Insulation resistance | Greater than 100 MΩ at 500 VDC |
| Electromagnetic Compatibility | Complies with GB/T 18268 (IEC 61326-1) |
| Weight | Approximately 160 grams |
| Frequency signal | High level ≥ 4 V; low level ≤ 1 V |
| Pulse width | ≥10us |
| Frequency range | 0.1 Hz to 50 kHz (signals below 0.1 Hz are treated as 0 Hz and removed) |
| Measurement resolution | 0.1Hz |
| Measurement cycle | 0.1s |
| Connected field devices | Two-wire frequency signal source |
Input data |
|
| Input signal | 0~50 kHz |
| Input impedance | ≥100 kΩ |
Output data |
|
| Output signal | 0~10V; 0~20mA |
| Output impedance | Current type ≤ 500 Ω; voltage type ≥ 10 kΩ |
| Output load | Current output ≤ 500 Ω; voltage output ≥ 10 kΩ |
Power supply |
|
| Supply voltage (Ue) | 24 VDC ±25% |
| Power Protection | Reverse Power Protection |
| Power consumption | <1W |
| Power Supply Method | Independent power supply |
| Power Connection Method | Terminal power supply; base power supply |
Size |
|
Base Power Supply |
|
| Depth | 121mm |
| Height | 113mm |
| Width | 13.3mm |
Terminal power supply |
|
| Depth | 110mm |
| Height | 108mm |
| Width | 13.3mm |
Housing |
|
| Materials | PC+ABS flame retardant |
| Protection Level | IP20 |
| Flame-retardant rating | UL94/V0 |
| Color | White + Gray |
EMC data |
|
| Electrical Fast Transient/Burst Immunity | Standards: IEC 61326-1; Class A |
| Surge (Impulse) Immunity | Standards: IEC 61326-1; Class B |
| Radio-frequency electromagnetic field radiation immunity | Standards: IEC 61326-1; Compliance with Essential Requirements |
| Electrostatic Discharge Immunity | Standards: IEC 61326-1; Class A |
| Immunity to Conducted Disturbances Induced by Radio-Frequency Fields | Standards: IEC 61326-1; Compliance with Essential Requirements |
| Low-Frequency Common-Mode Conduction | Standards: IEC 61326-1; Compliance with Essential Requirements |
Operating Environment |
|
| Continuous operating temperature | -20℃~+60℃ |
| Storage temperature | -40℃ to +80℃ |
| Relative humidity | <90% RH (no condensation) |
| Environmental Requirements | The surrounding environment shall be free from severe vibration, impact, and electromagnetic interference such as high currents and sparks. The air shall not contain any corrosive media that can attack chromium, nickel, or silver plating, nor shall it contain flammable or explosive substances. |
Connection Parameters |
|
| Wire cross-sectional area range | 0.5~2.5 mm² |
| Minimum Wire Cross-Sectional Area AWG | 12 |
| Maximum Conductor Cross-Sectional Area AWG | 24 |
| Wire stripping length | 8mm |
| Thread | M3 |
| Connection method | Screw connection |
| Minimum Tightening Torque | 0.5 Nm |
| Maximum Tightening Torque | 0.6 Nm |
Install |
|
| Installation Method | DIN 35 mm rail mounting |
| External dimensions | |||
![]() |
|||
| Installation Method | |||
![]() |
![]() |
![]() |
![]() |
Basic Parameters |
|
| Number of channels | 1 in, 2 out |
| Output accuracy (20°C) | 0.2% F.S. |
| Temperature drift | 50ppm/K |
| Response time | 1s (0–90%) (TYP) |
| Dielectric strength | 1500 VAC for 1 minute, 2 mA |
| Insulation resistance | Greater than 100 MΩ at 500 VDC |
| Electromagnetic Compatibility | Complies with GB/T 18268 (IEC 61326-1) |
| Weight | Approximately 160 grams |
| Frequency signal | High level ≥ 4 V; low level ≤ 1 V |
| Pulse width | ≥10us |
| Frequency range | 0.1 Hz to 50 kHz (signals below 0.1 Hz are treated as 0 Hz and removed) |
| Measurement resolution | 0.1Hz |
| Measurement cycle | 0.1s |
| Connected field devices | Two-wire frequency signal source |
Input data |
|
| Input signal | 0~50 kHz |
| Input impedance | ≥100 kΩ |
Output data |
|
| Output signal | 0~10V; 0~20mA |
| Output impedance | Current type ≤ 500 Ω; voltage type ≥ 10 kΩ |
| Output load | Current output ≤ 500 Ω; voltage output ≥ 10 kΩ |
Power supply |
|
| Supply voltage (Ue) | 24 VDC ±25% |
| Power Protection | Reverse Power Protection |
| Power consumption | <1W |
| Power Supply Method | Independent power supply |
| Power Connection Method | Terminal power supply; base power supply |
Size |
|
Base Power Supply |
|
| Depth | 121mm |
| Height | 113mm |
| Width | 13.3mm |
Terminal power supply |
|
| Depth | 110mm |
| Height | 108mm |
| Width | 13.3mm |
Housing |
|
| Materials | PC+ABS flame retardant |
| Protection Level | IP20 |
| Flame-retardant rating | UL94/V0 |
| Color | White + Gray |
EMC data |
|
| Electrical Fast Transient/Burst Immunity | Standards: IEC 61326-1; Class A |
| Surge (Impulse) Immunity | Standards: IEC 61326-1; Class B |
| Radio-frequency electromagnetic field radiation immunity | Standards: IEC 61326-1; Compliance with Essential Requirements |
| Electrostatic Discharge Immunity | Standards: IEC 61326-1; Class A |
| Immunity to Conducted Disturbances Induced by Radio-Frequency Fields | Standards: IEC 61326-1; Compliance with Essential Requirements |
| Low-Frequency Common-Mode Conduction | Standards: IEC 61326-1; Compliance with Essential Requirements |
Operating Environment |
|
| Continuous operating temperature | -20℃~+60℃ |
| Storage temperature | -40℃ to +80℃ |
| Relative humidity | <90% RH (no condensation) |
| Environmental Requirements | The surrounding environment shall be free from severe vibration, impact, and electromagnetic interference such as high currents and sparks. The air shall not contain any corrosive media that can attack chromium, nickel, or silver plating, nor shall it contain flammable or explosive substances. |
Connection Parameters |
|
| Wire cross-sectional area range | 0.5~2.5 mm² |
| Minimum Wire Cross-Sectional Area AWG | 12 |
| Maximum Conductor Cross-Sectional Area AWG | 24 |
| Wire stripping length | 8mm |
| Thread | M3 |
| Connection method | Screw connection |
| Minimum Tightening Torque | 0.5 Nm |
| Maximum Tightening Torque | 0.6 Nm |
Install |
|
| Installation Method | DIN 35 mm rail mounting |
| External dimensions | |||
![]() |
|||
| Installation Method | |||
![]() |
![]() |
![]() |
![]() |
文件名称
文件大小
所属分类
上传时间
预览下载
201.5KB
Signal isolator
2023-09-04
208.8KB
Signal isolator
2023-09-19
文件名称
所属分类
下载




