产品中心
DRG-1640 (four inputs, four outputs): digital input, relay output
所属分类:
DRG Series
The discrete-input isolated safety barrier accepts contact or proximity-switch inputs from the hazardous-area side and, via barrier isolation, transmits these signals to the safe-area output. It features relay-output configuration for switching between normally open and normally closed states.
通道数:
Four in, four out
输入:
配电:
输出:
供电方式:
电源连接方式 :
产品详情
技术参数
技术与安装
下载

Close
- 产品对比
去对比
Basic Parameters |
|
| Number of channels | 4 in, 4 out |
| On-site sensor-side supply voltage | Approximately 8 V (open circuit) |
| Response time | 20ms |
| Dielectric strength | 1500 VAC for intrinsically safe terminals vs. non-intrinsically safe terminals; 1000 VAC for non-intrinsically safe terminals vs. non-intrinsically safe terminals. |
| Insulation resistance | Non-intrinsically safe terminal–intrinsically safe terminal ≥ 100 MΩ; power supply–non-intrinsically safe terminal ≥ 100 MΩ. |
| Electromagnetic Compatibility | Complies with IEC 61326-1 (GB/T 18268) and IEC 61326-3-1. |
| Explosion-proof marking | [Ex ia Ga]ⅡC, [Ex ia Da]ⅢC |
| Weight | Approximately 150g |
| Connected field devices | Field devices such as proximity switches and limit switches compliant with DIN 19234 and NAMUR |
| Applicable Locations | Zone 0, Zone 1, Zone 2; IIA, IIB, IIC hazardous areas |
| Signal Input Characteristics | When the on-site input current exceeds 2.1 mA, it indicates ON. |
| When the on-site input current exceeds 1.2 mA, it indicates OFF. | |
| Switch hysteresis: 200 µs | |
| Function of Switch Settings | When in the ON state, the input and output are reversed, and a wiring fault detection function is provided. |
| In the OFF state, the input and output are in phase, and there is no circuit fault detection function. | |
| Relay Output Characteristics |
Response time: 20 ms |
| Driving capability: 250 VAC/2 A, 30 VDC/2 A | |
Input data |
|
| Input signal | Switch |
Output data |
|
| Output signal | Relay |
Power supply |
|
| Power Supply | 20~35V DC |
| Power Protection | Reverse Power Protection |
| Power consumption | 2.5W |
| Power Supply Method | Independent power supply |
| Power Connection Method | Base power supply; terminal power supply |
Size |
|
Centralized power supply |
|
| Depth | 120.8mm |
| Height | 113mm |
| Width | 18.3mm |
Independent power supply |
|
| Depth | 110mm |
| Height | 108mm |
| Width | 18.3mm |
Housing |
|
| Materials | PC+ABS flame retardant |
| Protection Level | IP20 |
| Flame-retardant rating | UL94/V0 |
| Color | White + Gray |
EMC data |
|
| Electrical Fast Transient/Burst Immunity | Standards: IEC 61326-1; Class A |
| Surge (Impulse) Immunity | Standards: IEC 61326-1; Class B |
| Radio-frequency electromagnetic field radiation immunity | Standards: IEC 61326-1; Compliance with Essential Requirements |
| Electrostatic Discharge Immunity | Standards: IEC 61326-1; Class A |
| Immunity to Conducted Disturbances Induced by Radio-Frequency Fields | Standards: IEC 61326-1; Compliance with Essential Requirements |
| Low-Frequency Common-Mode Conduction | Standards: IEC 61326-1; Compliance with Essential Requirements |
Operating Environment |
|
| Continuous operating temperature | -20℃~+60℃ |
| Storage temperature | -40℃~+80℃ |
| Relative humidity | 10%~90% |
| Environmental Requirements | The surrounding environment shall be free from severe vibration, impact, and electromagnetic interference such as high currents and sparks. The air shall not contain any corrosive media that can attack chromium, nickel, or silver platings, nor shall it contain flammable or explosive substances. |
Connection Parameters |
|
| Wire cross-sectional area range | 0.5~2.5 mm² |
| Minimum Wire Cross-Sectional Area AWG | 24 |
| Maximum Conductor Cross-Sectional Area AWG | 12 |
| Wire stripping length | 8mm |
| Thread | M3 |
| Connection method | Screw connection |
| Minimum Tightening Torque | 0.5 Nm |
| Maximum Tightening Torque | 0.6 Nm |
Install |
|
| Installation Method | DIN 35 mm rail mounting |
| External dimensions | |||
| Base-centralized power supply type | Terminal-powered | ||
![]() |
![]() |
||
| Installation Method | |||
![]() |
![]() |
![]() |
![]() |
Basic Parameters |
|
| Number of channels | 4 in, 4 out |
| On-site sensor-side supply voltage | Approximately 8 V (open circuit) |
| Response time | 20ms |
| Dielectric strength | 1500 VAC for intrinsically safe terminals vs. non-intrinsically safe terminals; 1000 VAC for non-intrinsically safe terminals vs. non-intrinsically safe terminals. |
| Insulation resistance | Non-intrinsically safe terminal–intrinsically safe terminal ≥ 100 MΩ; power supply–non-intrinsically safe terminal ≥ 100 MΩ. |
| Electromagnetic Compatibility | Complies with IEC 61326-1 (GB/T 18268) and IEC 61326-3-1. |
| Explosion-proof marking | [Ex ia Ga]ⅡC, [Ex ia Da]ⅢC |
| Weight | Approximately 150g |
| Connected field devices | Field devices such as proximity switches and limit switches compliant with DIN 19234 and NAMUR |
| Applicable Locations | Zone 0, Zone 1, Zone 2; IIA, IIB, IIC hazardous areas |
| Signal Input Characteristics | When the on-site input current exceeds 2.1 mA, it indicates ON. |
| When the on-site input current exceeds 1.2 mA, it indicates OFF. | |
| Switch hysteresis: 200 µs | |
| Function of Switch Settings | When in the ON state, the input and output are reversed, and a wiring fault detection function is provided. |
| In the OFF state, the input and output are in phase, and there is no circuit fault detection function. | |
| Relay Output Characteristics |
Response time: 20 ms |
| Driving capability: 250 VAC/2 A, 30 VDC/2 A | |
Input data |
|
| Input signal | Switch |
Output data |
|
| Output signal | Relay |
Power supply |
|
| Power Supply | 20~35V DC |
| Power Protection | Reverse Power Protection |
| Power consumption | 2.5W |
| Power Supply Method | Independent power supply |
| Power Connection Method | Base power supply; terminal power supply |
Size |
|
Centralized power supply |
|
| Depth | 120.8mm |
| Height | 113mm |
| Width | 18.3mm |
Independent power supply |
|
| Depth | 110mm |
| Height | 108mm |
| Width | 18.3mm |
Housing |
|
| Materials | PC+ABS flame retardant |
| Protection Level | IP20 |
| Flame-retardant rating | UL94/V0 |
| Color | White + Gray |
EMC data |
|
| Electrical Fast Transient/Burst Immunity | Standards: IEC 61326-1; Class A |
| Surge (Impulse) Immunity | Standards: IEC 61326-1; Class B |
| Radio-frequency electromagnetic field radiation immunity | Standards: IEC 61326-1; Compliance with Essential Requirements |
| Electrostatic Discharge Immunity | Standards: IEC 61326-1; Class A |
| Immunity to Conducted Disturbances Induced by Radio-Frequency Fields | Standards: IEC 61326-1; Compliance with Essential Requirements |
| Low-Frequency Common-Mode Conduction | Standards: IEC 61326-1; Compliance with Essential Requirements |
Operating Environment |
|
| Continuous operating temperature | -20℃~+60℃ |
| Storage temperature | -40℃~+80℃ |
| Relative humidity | 10%~90% |
| Environmental Requirements | The surrounding environment shall be free from severe vibration, impact, and electromagnetic interference such as high currents and sparks. The air shall not contain any corrosive media that can attack chromium, nickel, or silver platings, nor shall it contain flammable or explosive substances. |
Connection Parameters |
|
| Wire cross-sectional area range | 0.5~2.5 mm² |
| Minimum Wire Cross-Sectional Area AWG | 24 |
| Maximum Conductor Cross-Sectional Area AWG | 12 |
| Wire stripping length | 8mm |
| Thread | M3 |
| Connection method | Screw connection |
| Minimum Tightening Torque | 0.5 Nm |
| Maximum Tightening Torque | 0.6 Nm |
Install |
|
| Installation Method | DIN 35 mm rail mounting |
| External dimensions | |||
| Base-centralized power supply type | Terminal-powered | ||
![]() |
![]() |
||
| Installation Method | |||
![]() |
![]() |
![]() |
![]() |
文件名称
文件大小
所属分类
上传时间
预览下载
172.6KB
Safety barrier
2024-04-03
208.8KB
Signal isolator
2023-09-19
144.4KB
Signal isolator
2023-09-19
文件名称
所属分类
下载





